M.Sc. student in Petroleum and Mineral Resources Engineering, BUET
I trained as a chemical engineer and now work on storing CO2 underground. For my M.Sc. I build compositional reservoir simulation models of CO2 storage in CMG GEM.
Fig. 1. A capture plant, a pipeline and an injection well. Scroll and CO2 travels down the well to a storage formation 2,000 m below. The strip under the menu shows typical pressure and temperature at each depth, and the state CO2 is in.
About
I am an M.Sc. student in the Department of Petroleum and Mineral Resources Engineering at Bangladesh University of Engineering and Technology (BUET), supervised by Dr. Shahriar Mahmud. My research is on carbon capture, utilisation and storage. I build compositional models of CO2 storage in the CMG reservoir simulation suite, and my thesis question is being defined around injection performance and storage security.
My first degree is a B.Sc. in Applied Chemistry and Chemical Engineering from the University of Rajshahi. My thesis there reviewed how MXene materials are made, what their properties are and how they are used to remove pollutants. In 2023 I also completed four weeks of training in industrial unit operations and process control at the Training Institute for Chemical Industries.
Alongside my thesis work I have modelled a gas-condensate well in PROSPER, studied why production is declining at a shallow gas reservoir in the Bhola gas field, and followed deep-well drilling and wireline logging at the Titas-31 well. Outside the university I serve as Director of Phulkuri Asar, Dhaka City Dishari, where I lead development programmes for children and young people.
Research interests
Carbon capture, utilisation and storage
Geological CO2 storage
Injection optimisation
Compositional and coupled reservoir simulation
Caprock and fault integrity
Machine-learning surrogate modelling
Uncertainty quantification
Name
Syed Kamrul Ahsan
Programme
M.Sc. in Petroleum and Mineral Resources Engineering
Institution
Bangladesh University of Engineering and Technology (BUET), Dhaka
Supervisor
Dr. Shahriar Mahmud
Research area
CO2 storage, reservoir simulation
First degree
B.Sc. in Applied Chemistry and Chemical Engineering, University of Rajshahi
Based in
Dhaka, Bangladesh
Page updated
November 2026
Education
Ongoing
M.Sc. in Petroleum and Mineral Resources Engineering
Bangladesh University of Engineering and Technology (BUET), Dhaka
CGPA 3.21/4.00
Supervisor: Dr. Shahriar Mahmud
Thesis topic under definition. Current research is on carbon capture, utilisation and storage using the CMG reservoir simulation suite.
Graduate coursework
Reservoir Engineering (PMRE 6001)
Advanced Reservoir Engineering (PMRE 6002)
Well Logging and Formation Evaluation (PMRE 6003)
Petroleum Production Engineering (PMRE 6005)
Well Test Analysis (PMRE 6006)
Advanced Natural Gas Engineering (PMRE 6008)
Reservoir Simulation (PMRE 6010)
Petroleum Geology (PMRE 6014)
Petrophysics and Fluid Flow Laboratory
Analytical and Testing Laboratory
Completed
B.Sc. in Applied Chemistry and Chemical Engineering
University of Rajshahi, Rajshahi
CGPA 3.48/4.00
Supervisor: Prof. Dr. Nayeem Faruqui
Thesis: Methods of Synthesis, Characteristics and Environmental Application of MXene Materials
Research
M.Sc. researchOngoing
Carbon Capture, Utilisation and Storage
In short: reservoir simulation of CO2 injected into a storage formation, to see how well it goes in and whether it stays there.
Department of Petroleum and Mineral Resources Engineering, BUET. Supervisor: Dr. Shahriar Mahmud
Building compositional reservoir simulation models of CO2 storage in the CMG suite (GEM). The thesis question is being defined around injection performance and storage security.
Developing the modelling workflow that will support the study: fluid description, injection scheduling, and assessment of pressure and plume evolution in the storage formation.
The modelling workflow
Fluid description
Injection schedule
Pressure and plume evolution
CMG GEM
Compositional simulation
CO2 storage
Why storage is deep: CO2 on the way down a well
At 2,000 m: about 201 bar and 75 °C. CO2 is supercritical.
Background physics, drawn for this page. It is not a result of my research. Conditions follow typical gradients: 25 °C at the surface, then 25 °C and about 100 bar for every kilometre. Phase boundary from the Span and Wagner equation for CO2.
Co-authored manuscriptIn preparation, 2026
An Integrated Approach to Carbon Capture, Utilization, and Storage (CCUS) for Sustainable CO2 Management
In short: an assessment of the whole CCUS chain for Bangladesh, from capture at the plant to storage in depleted gas fields.
With M. Hassan and S. N. Ahsan
Models post-combustion capture with monoethanolamine (MEA) for a gas-fired combined-cycle power plant and for the reformer flue gas of an ammonia fertilizer plant, including the energy the solvent needs in a hot climate.
Follows the captured CO2 through compression and pipeline transport to storage in depleted gas fields, and considers using high-purity fertilizer CO2 to make urea.
Links a techno-economic assessment to a life-cycle assessment that covers domestic gas and imported LNG, with cost and emissions quantified under uncertainty.
Post-combustion capture
Techno-economic assessment
Life-cycle assessment
Uncertainty analysis
The chain that is assessed
CO2 sourcesgas power plant, ammonia plant
CaptureMEA solvent
Compression and pipeline
Storagedepleted gas fields
Also considered: fertilizer CO2 used to make urea
Three findings, in words
Stack and life-cycle emissionsCapture removes most of the power plant's stack CO2. Over the life cycle the reduction is smaller, because methane and the LNG chain remain.
Hot climateIt raises the energy the solvent needs only slightly, and adds little to the cost of CO2 avoided.
Cost of adding CCSThe national master plan's figure leaves out the energy penalty of capture.
Course research projectSpring 2026PMRE 6005
Nodal Analysis and Production Optimisation of a Gas-Condensate Well
In short: a single-well model that shows how much gas the well can deliver and what limits it.
Department of Petroleum and Mineral Resources Engineering, BUET
Built a single-well nodal model in Petroleum Experts PROSPER with a black-oil PVT description, a cased-hole completion and wellbore model, and Mukherjee–Brill vertical lift performance solved at the bottom node.
Regressed the inflow performance relationship on four stabilised multirate test points with the back-pressure (C and n) model. The fit gave a deliverability exponent of 0.845 and an absolute open flow potential of about 29.9 MMscf/d, verified by independent hand calculation.
Quantified the sensitivity of deliverability to tubing inside diameter, wellhead backpressure and water-gas ratio, and evaluated performance at 60 per cent reservoir depletion.
Screened the operating points against API RP 14E erosional velocity limits and the Turner criterion for liquid loading.
Deliverability exponent, n
0.845
Absolute open flow
29.9MMscf/d
Multirate test points
4
PROSPER
Black-oil PVT
Back-pressure IPR
Mukherjee–Brill VLP
API RP 14E
Turner criterion
Inflow performance of the well
At 50 % of reservoir pressure the well delivers about 23.4 MMscf/d, 78 % of its open-flow potential.
Drawn from the two fitted values above with the back-pressure equation. The dashed curves show the same open flow with n = 1 (laminar flow) and n = 0.5 (fully turbulent flow). The test points and the tubing curve are in the project report.
Field studyAugust 2026
Production Decline Analysis of a Shallow Gas Reservoir Producing Gas and Water
Bhola gas field, Bangladesh
Investigated the declining production of a shallow gas reservoir that produces gas and water at the same time.
Identified the reservoir and production-related causes of the decline, and evaluated strategies for improving and sustaining gas deliverability.
Decline analysis
Gas deliverability
B.Sc. thesisUniversity of Rajshahi
Methods of Synthesis, Characteristics and Environmental Application of MXene Materials
Department of Applied Chemistry and Chemical Engineering. Supervisor: Prof. Dr. Nayeem Faruqui
Reviewed the structure, synthesis routes and properties of MXenes, a family of two-dimensional transition-metal carbides and nitrides.
Covered their use in removing pollutants such as radionuclides, uranium, thorium and dyes by adsorption, photocatalysis and membrane separation, and the open challenges in making and using them.
Literature review
2D materials
Water treatment
The line drawings on this page are schematics drawn for the site. They show the idea of each study and are not results.
Field and industrial exposure
July 2026Titas gas field, Brahmanbaria
Deep Well Drilling and Well Logging Field Study, Titas-31
CCDC-operated drilling project
Observed deep-well drilling operations at the rig site, including drilling-fluid circulation, well-control practice and drilling equipment in service.
Followed wireline logging and formation-evaluation operations, and how the resulting data are interpreted to assess hydrocarbon potential in the target formations.
Drilling operations
Well control
Wireline logging
Formation evaluation
Drilling-fluid circulation at a rig
Mud pit
Mud pump
Standpipe and hose
Drill string
Bit
Annulus
Shale shaker
General schematic, drawn for this page. It is not the layout of the Titas-31 rig.
Training and certificates
Date
Course or event
Held by
Document
May to Jun 2023
Industrial Process Unit Operation and Process Control Technique Four weeks, grade A
Training Institute for Chemical Industries (TICI), Polash, Narsingdi. Central training institute of BCIC